1.दुरि नाप्नुपर्ने दुई बिन्दुहरुको बिचमा खाल्डो खोल्सी आदि छ भने यो दुरि कुन यन्त्रले नापिन्छ ?
2. Benchmark is established by
3. Overturing of vehicles on a curve can be avoided by
4. जाँच गर्न तोकिएको इन्जिनियर वा कर्मचारीले कति दिन भित्र आफ्नो प्रतिवेदन दिनुपर्छ ?
5. स्थानीय सरकार संचालन ऐन २०७४ को अनुसार कुन दफामा नक्सा हेरफेर गर्ने व्यवस्था उल्लेखित गरिएको छ
6. The stone suitable for rubble masonry should be
7. The minimum numbers of steps in a flight should not be less than
8. Paints with white lead are suitable for painting of
9. Shear stress on principal plane is
10. Laminated springs are subjected to
11. A long column has maximum crippling load when its
12. The maximum shear stress occurs at
13. The discharge over broad crested weir is maximum when the depth of flow is
14. For maximum discharge in a circular channel section, the ratio of the depth of the flow to that of diameter is
15. The Froude number is the ratio of inertia force to
16. An independent mass of fluid doesnot posses
17. If the plasticity of a soil mass is zero, the soil is
18.सुदूरपश्चिम प्रदेश सुशासन ऐन, २०७५,आनुसार "प्रशासनिक कार्य सम्पादन गर्दा अपनाउनु पर्ने कार्यविधि" परिच्छेद आन्तरगर्त पर्दछ?
19. The coefficient of active earth pressure for a loose sand having an angle of internal friction is 300 is
20. The effective size of particle of soil is given by
21. The maximum diameter of bars in a beam is limited to
22. A flat slab is supported
23. Main reinforcement in beam is used for
24. Surface vibrator is only effective when thickness of concrete does not exceed
25. The thickened portion of masonry wall is called
26. When DPC is to be laid over large areas, the material preferred is
27. Cement used for resisting of acid is
28. The roof preferred for large span is
29. The maximum discharge of a tube well is about
30. On standard silica scale , the turbidity in drinking water should be limited to
31. The effect of increasing diameter of sewer on the self cleansing velocity is
32. Standard BOD is measured at
33. Hydrograph is the graphical representation of
34. The major resisting force of gravity dam is
35. The elementary profile of dam is
36. A straight glacis type fall with a baffle platform and baffle wall is called
37. If the RL of a canal bed and HFL of drainage are 212m and 210m respectively, then cross drainage work will be
38. Silt excluders are constructed on the
39. Compared to a level surface, on a descending gradient the stopping sight distance is
40. Which of the following shapes is preferred in a valley curve?
42. The maximum allowable Los Angeles abrasion value of high quality surface course is
43. For sandy soil the most common method of stabilization is
44. The penetration test on bitumen is used for determining its
45. Volume is measured correct to the nearest
46. Normally which one contract gives the maximum value of project
48. The time with which direct cost does not reduced with increase in time is known as
49. Construction joints are generally provided in concrete ?
50. निजामती सेवा नियमावली 2050 कसले तयार पारेको हो ?