SUDURPASCHIM ONLINE MODEL EXAM SET 19 ( ASSISTANT SUB ENGINEER)

1. The smaller horizontal angle between the true meridian and a survey line, is known

2. Closed traverse is suitable in the survey of :

3. The surveying used to determine additional details such as boundaries of filed is called

4. In chain surveying field work is limited to

5. The survey in which the curvature of earth is ignored, is called as:

6. Which of the following is the most accurate estimate?

7.Revised estimate is prepared when the sanctioned original detailed estimate exceed by?

8. The necessary element of an estimate are:

9. Gneiss is obtained from

10. The strength of cement is reduced by...............after 24 months

11. Finishing of motar point is called

12. The Lower level of window where it rests is called .......in a building.

14. The strength and quality of concrete depends on.

15. The maximum buckling factor for sand is

16. The operation during the infiltration of water below the ground surface, is

17. The other name of unconfined aquifer is

18. Sewerage system is designed for

19. The full form of PPR (pipes used in plumbing)

20. The RF (representative factor) for scale of 1cm = 25km is

21. Which of the following building material are locally available material in ancient period of time.

22. Dimension lines and projection lines in drawing are shown by?

23. The unseen/inner edges of object is represented by?

24. Which line type is thin and light ?

25. Traffic density depend upon the………. Of vehicle

26. WBM is one of the ........ type of Road Pavement

27. First stage of deciding alignment of hill road is

28. Penetration test of bitumen is carried out to determine

29. Super Elevation is provided in curved roads

30. For brick construction, the lime sand motar is

31. निजामती सेवा ऐनअनुसार भविष्यमा सरकारी सेवाको निम्ति अयोग्य नठहरिने गरी सेवाबाट हटाउने विभागीय सजाय कस्तो सजाय हो ?

32. The left by a landowner between road( right of way) and building is :

33. The minimum number of abutments in a bridge should be

34.निजामती कर्मचारीको अध्ययन बिदा कसले स्वीकृत गर्छ ?

35. गाउँपालिका/ नगरपालिकाको प्रत्येक आर्थिक वर्षको बजेट पेश कहिले सम्म गर्नु पर्छ ?

36 Which one of the following does not take load in suspension bridge ?

37. The most commonly adopted method of irrigation for cereal crop is

38. The ratio of total volume of water delivered to a crop, to the area on which it has been spread, is called

39. A silt regulator located at the head of a channel is called

40. Main purpose of maintenance of irrigation system is

41. Minimum size of pipe connected in septic tank is

42. The pressure at inlet and outlet in break pressure tank is

43. Inverted siphon is called

44. In case of unsewered areas, an additional provision for septic tank is usually

45. Which of the following is not a common size of reinforcement bars

46. When 1 cm on a drawing represents 1m length in reality, the scale is said to be:

47. If the level of source of water is higher than that of the place of consumption the system adoption for supplying water is

48. The unit of measurement of full brick thick wall is

49.सुदूरपश्चिम प्रदेश सुशासन ऐन, २०७५,आनुसार "प्रशासनिक कार्य सम्पादन गर्दा अपनाउनु पर्ने कार्यविधि" परिच्छेद आन्तरगर्त पर्दछ?

50. In urban area, which among is the following popular land development tools