1. The text height for room names should be set to ......... for a drawing that will be plottedto a scale of 1/4" - 1'-0",
2. In Engineering Drawing, space between two sentences should be left equal
3. The point of intersection of co-ordinate axis is called
4. Set squares are not used to draw
5. Generally, the units used on an architectural drawing are set to
6. In long and short wall method of estimation, the length of long wall is the centre to centre distance between the walls and
7. The unit of measurement for 10 cm thick brick wall is
8. Compute the amount of cement required for 10 m3 RCC having M20 (1:1.5:3
9. The volume of cement required to prepare 100 cubic meter of 1:2:4 concrete is
10. Due to change in price level, a revised estimate is prepared if the sanctioned estimate exceeds
11. рдирдпрд╛рдБ рдирд┐рдпреБрдХреНрддрд┐ рд╣реБрдиреЗ рдирд┐рдЬрд╛рдорддреА рдХрд░реНрдордЪрд╛рд░реАрд▓реЗ рдирд┐рдпреБрдХреНрддрд┐ рднрдПрдХреЛ рдХрддрд┐ рджрд┐рдирднрд┐рддреНрд░ рдЖрдлреНрдиреЛ рд╕рдореНрдкрддреНрддрд┐ рд╡рд┐рд╡рд░рдгрдкреЗрд╢ рдЧреБрд░реНрдирдкрд░реНрдЫ ?
12. The 'fix' of a plane table station with three known points, is bad if the plane table stationlies
13. The smaller horizontal angle between the true meridian and a survey line, is known
14. Closed contours of decreasing values towards their centre, represent
15. The bearings of the lines AB and BC are 146┬░ 30' and 68┬░ 30'. The included angle ABC is
16. The rock generally used for roofing, is
17. The objective of surveying is to prepare
20. The most weather resisting metamorphic rock is
21. During production of cement raw materials are mixed in
22. If P is the percentage of water required for normal consistency, water to be added for determination of initial setting time is,
23. In the sieve analysis of fineness test, the residue on IS sieve no 9 after 15 minutes of sieving should not be more than
25. The following elements of a paint is used as base, pigment, as well as drier
26. During compressive strength load is applied at the rate of
27. Normally the wood used for scaffolding is
28. Teak wood is suitable for
29. The shape of the bull trench kiln is
30. A grillage foundation
31. Residual soils are formed by
32. In cold water curing should be contained for......days
33. The size of fine aggregate does not exceed
34. The maximum buckling factor for sand is
35. Which types of power supply system is needed if small amount of power is required?
36. The devices installed for drawing water from the sources are called
37. Cement concrete floor is laid in a ratio of:
38. Local road are responsibility of
39. Which of the following is not the type of cross drain
40. рдирд┐рдЬрд╛рдорддреА рд╕реЗрд╡рд╛ рдРрди, 2049 рдорд╛ рдХрддрд┐ рдкрд░рд┐рдЪреНрдЫреЗрдж рд░ рджрдлрд╛ рдЫрдиреН ?
43. First structures in the irrigation work is
44. In hilly area with rock exposed, generally the most suitable canal type is
45. Cross slope of road (camber) is
46. The Valve used for precisely adjusting the volume of flow is called
47. The first stage of construction is
48. The bearing capacity of a soil
49. Quarry sap is found in
50. The lower water- cement ratio in concrete products
bashubudha25@gmail.com
Ans sheet kata baatw line ni sir
Gmail bata Online Result aauxa Inbox spam Folder aaauxa